View HA17324AF_4245967.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

HA17324A Series
Quad Operational Amplifier
REJ03D0674-0400 Rev.4.00 Mar 10, 2006
Description
HA17324A series are quad operational amplifier that provide high gain and internal phase compensation, with single power supply. They can be widely used to control equipments.
Features
* * * * Wide range of supply voltage, and single power supply used Internal phase compensation Wide range of common mode voltage, and possible to operate with an input about 0 V Low electro-magnetic susceptibility level
Measurement Condition
Rf Vcc = +7.5 V Vee = -7.5 V Rs Rs Rf 0.01 Vin -10 dBm RF signal source (for quasi-RF noise) Vout V (= 100Vio) _
5.0
Output Offset Voltage vs. Input Interference
Output offset voltage (arb. unit)
- +
4.0 3.0 2.0 1.0 0 -1.0 100E+3 HA17324A series HA17324 series
Improvement
1E+6
10E+6 100E+6 1E+9 Input RF frequency (Hz)
10E+9
Ordering Information
Type No. HA17324A HA17324AF HA17324ARP HA17324AT Application Commercial use Package Name DIP-14 pin SOP-14 pin (JEITA) SOP-14 pin (JEDEC) TSSOP-14 pin Package Code PRDP0014AB-B PRSP0014DF-B PRSP0014DE-A PTSP0014JA-B
Rev.4.00 Mar 10, 2006 page 1 of 7
HA17324A Series
Pin Arrangement
Vout1 Vin(-)1 Vin(+)1 VCC Vin(+)2 Vin(-)2 Vout2 1 2 3 4 5 6 7 (Top view) -+ 2 +- 3 1 -+ 4 +- 14 Vout4 13 Vin(-)4 12 Vin(+)4 11 VEE 10 Vin(+)3 9 8 Vin(-)3 Vout3
Circuit Schematic (1/4)
Q5 Vin(-) Q1 Q2 Q3 Q4 Q6 C Q7 R1 Vin(+) Q11 Q10 Q8 Q9 Q12 Q13 Vout
Note: If Input/Output terminals voltage over the absolute maximum ratings, there is possibility of mis-operation, characteristics deterioration and destruction, because of the current's flowing to parasitic diode in IC. The Input/Output terminals are recommended to be protected with the clamp circuit which using the diode with low forward voltage (like schottky barrier diode) when there is a possibility for the Input/Output terminals voltage exceeds the absolute maximum ratings.
Rev.4.00 Mar 10, 2006 page 2 of 7
HA17324A Series
Absolute Maximum Ratings
(Ta = 25C)
Item Power supply voltage Output sink current Common mode input voltage Differential input voltage Output voltage Allowable power dissipation Symbol VCC Iosink VCM Vin(diff) Vout PT Ratings 32 50 -0.3 to +VCC VCC -0.3 to +VCC 625 *2 625 *3 400 *4 -40 to +85 -55 to +125 Unit V mA V V V mW
DIP SOP TSSOP
Operating temperature Storage temperature
Topr Tstg
C C
Notes: 1. HA17324A: This is the allowable values up to Ta = 50C. Derate by 8.3 mW/C. 2. HA17324AF/ARP: When it is mounted on glass epoxy board of 40 mm x 40 mm x 1.6 mmt with 10% wiring density, value at Ta 25C. If Ta > 25C, derated by 6.25 mW/C. When it is mounted on glass epoxy board of 40 mm x 40 mm x 1.6 mmt with 30% wiring density. If Ta > 32C, derated by 6.70 mW/C. 3. HA17324AT: These are the allowable values up to Ta = 25C. Derate by 4 mW/C above that temperature.
Electrical Characteristics
(VCC = +15 V, Ta = 25C)
Item Input offset voltage Input offset current Input bias current Power source rejection ratio Voltage gain Common mode rejection ratio Common mode input voltage range Maximum output voltage Output source current Output sink current Supply current Slew rate Channel separation *1 Output sink current Output voltage Output voltage Note: 1. Design spec. Symbol VIO IIO IIB PSRR AVD CMR VCM VOP-P Iosource Iosink ICC SR CS Iosink VOH1 VOH2 VOL1 VOL2 Min 75 -0.3 20 10 15 3 13.2 12.0 Typ 2 5 30 93 90 80 13.6 40 20 0.8 0.19 (120) 50 9 13.6 13.3 0.8 1.1 Max 7 50 500 13.5 2 1.0 1.8 Unit mV nA nA dB dB dB V V mA mA mA V/s dB A mA V V V V Test Conditions VCM = 7.5 V, RS = 50 , Rf = 50 k VCM = 7.5 V, IIO = | II (-) - II (+) | VCM = 7.5 V f = 100 Hz, RS = 1 k, Rj = 100 k RS = 1 k, Rf = 100 k, RL = RS = 50 , Rf = 5 k RS = 1 k, Rf = 100 k, f = 100 Hz f = 100 Hz, RS = 1 k, Rf = 100 k, RL = 20 k VIN+ = 1 V, VIN- = 0 V, VOH = 10 V VIN = 0 V, VIN = 1 V, VOL = 2.5 V VIN = GND, RL = f = 1.5 kHz, VCM = 7.5 V, RL = f = 1 kHz VIN+ = 0 V, VIN- = 1 V, VOL = 200 mV VIN+ = 0 V, VIN- = 1 V, VOL = 1 V IOH = -1 mA IOH = -10 mA IOL = 1 mA IOL = 10 mA
Rev.4.00 Mar 10, 2006 page 3 of 7
HA17324A Series
Characteristic Curves
Output source current Iosource (mA)
Input bias current IIB (nA)
Output Source Current vs. Ambient Temperature 80 VCC = 15 V 70 VOH = 10 V 60
50 40 30 20 10 0 -20 0 20 40 60 Ambeint temperature Ta (C) 80
Input Bias Current vs. Ambient Temperature
80 70 60 50 40 30 20 10 0 -20 0 20 40 60 Ambeint temperature Ta (C) 80 VCC = 15 V VCM = 7.5 V
Supply Current vs. Supply Voltage
4
Supply current ICC (mA) Input bias current IIB (nA)
Input Bias Current vs. Supply Voltage
80 Ta = 25C
Ta = 25C
3
60
2
40
1
20
0
8 16 24 32 Supply voltage VCC (V)
40
0
8 16 24 32 Supply voltage VCC (V)
40
Voltage Gain vs. Supply Voltage
Maximum output voltage VOP-P (V)
Maxlmum Output Voltage vs. Frequency
20 16 12 8 4 0 1k VCC = 15 V Ta = 25C RL = 20 k
160
Voltage gain AVD (dB)
Ta = 25C RL = 120
80
40
0
8 16 24 32 Supply voltage VCC (V)
40
3k
10 k 30 k 100 k 300 k Frequency f (Hz)
1M
Rev.4.00 Mar 10, 2006 page 4 of 7
HA17324A Series
Voltage Gain vs. Frequency 120 100
Voltage gain AVD (dB)
VCC = 15V Ta = 25C RL =
80 60 40 20 0 1 3 10 30 100 300 1k 3k Frequency f (Hz) 10 k 30 k 100 k 300 k 1M
Common Mode Rejection Ratio vs. Frequency 120
Common mode rejection ratio CMR (dB)
100
VCC = 15V Ta = 25C RS = 50
80
60
40
20
0 100
300
1k
3 k 10 k 30 k 100 k 300 k Frequency f (Hz)
1M
Rev.4.00 Mar 10, 2006 page 5 of 7
HA17324A Series
Package Dimensions
JEITA Package Code P-DIP14-6.3x19.2-2.54 RENESAS Code PRDP0014AB-B Previous Code DP-14AV MASS[Typ.] 0.97g
D
14
8
1 b3
7
Z
A
E
Reference Symbol
A1
Dimension in Millimeters
Min
e
bp
e1
c
( Ni/Pd/Au plating )
e1 D E A A1 bp b3 c e Z L
Nom Max 7.62 19.2 20.32 6.3 7.4 5.06
L
0.51 0.40 0.48 0.56 1.30 0.19 0.25 0.31 0 15 2.29 2.54 2.79 2.39 2.54
JEITA Package Code P-SOP14-5.5x10.06-1.27
RENESAS Code PRSP0014DF-B
Previous Code FP-14DAV
MASS[Typ.] 0.23g
*1
D 8
F
14
NOTE) 1. DIMENSIONS"*1 (Nom)"AND"*2" DO NOT INCLUDE MOLD FLASH. 2. DIMENSION"*3"DOES NOT INCLUDE TRIM OFFSET.
bp
HE
E
Index mark
*2
Terminal cross section ( Ni/Pd/Au plating )
1 Z e
*3
7 bp x M L1
Reference Dimension in Millimeters Symbol
c
A1
y
L
Detail F
D E A2 A1 A bp b1 c c1 HE e x y Z L L1
Min Nom Max 10.06 10.5 5.50
0.00 0.10 0.20 2.20 0.34 0.40 0.46 0.15 0.20 0.25 0 8 7.50 7.80 8.00 1.27 0.12 0.15 1.42 0.50 0.70 0.90 1.15
Rev.4.00 Mar 10, 2006 page 6 of 7
A
HA17324A Series
JEITA Package Code P-SOP14-3.95x8.65-1.27 RENESAS Code PRSP0014DE-A Previous Code FP-14DNV MASS[Typ.] 0.13g
*1
D 8
F
14
NOTE) 1. DIMENSIONS"*1 (Nom)"AND"*2" DO NOT INCLUDE MOLD FLASH. 2. DIMENSION"*3"DOES NOT INCLUDE TRIM OFFSET.
bp
*2
Index mark
HE
E
Terminal cross section ( Ni/Pd/Au plating )
1 Z e
*3
c
Reference Dimension in Millimeters Symbol
Min
7 bp x M L1
A1
L
y
Detail F
D E A2 A1 A bp b1 c c1 HE e x y Z L L1
Nom Max 8.65 9.05 3.95
0.10 0.14 0.25 1.75 0.34 0.40 0.46 0.15 0.20 0.25 0 8 5.80 6.10 6.20 1.27 0.25 0.15 0.635 0.40 0.60 1.27 1.08
JEITA Package Code P-TSSOP14-4.4x5-0.65
RENESAS Code PTSP0014JA-B
Previous Code TTP-14DV
MASS[Typ.] 0.05g
*1
D
A
F 8
14
NOTE) 1. DIMENSIONS"*1 (Nom)"AND"*2" DO NOT INCLUDE MOLD FLASH. 2. DIMENSION"*3"DOES NOT INCLUDE TRIM OFFSET.
bp
HE
*2
E
Index mark
Terminal cross section ( Ni/Pd/Au plating )
1 Z e
*3
c
7 bp x M L1
Reference Dimension in Millimeters Symbol
A1
L
y
Detail F
D E A2 A1 A bp b1 c c1 HE e x y Z L L1
Min Nom Max 5.00 5.30 4.40
0.03 0.07 0.10 1.10 0.15 0.20 0.25 0.10 0.15 0.20 0 8 6.20 6.40 6.60 0.65 0.13 0.10 0.83 0.4 0.5 0.6 1.0
Rev.4.00 Mar 10, 2006 page 7 of 7
A
Sales Strategic Planning Div.
Keep safety first in your circuit designs!
Nippon Bldg., 2-6-2, Ohte-machi, Chiyoda-ku, Tokyo 100-0004, Japan
1. Renesas Technology Corp. puts the maximum effort into making semiconductor products better and more reliable, but there is always the possibility that trouble may occur with them. Trouble with semiconductors may lead to personal injury, fire or property damage. Remember to give due consideration to safety when making your circuit designs, with appropriate measures such as (i) placement of substitutive, auxiliary circuits, (ii) use of nonflammable material or (iii) prevention against any malfunction or mishap. Notes regarding these materials 1. These materials are intended as a reference to assist our customers in the selection of the Renesas Technology Corp. product best suited to the customer's application; they do not convey any license under any intellectual property rights, or any other rights, belonging to Renesas Technology Corp. or a third party. 2. Renesas Technology Corp. assumes no responsibility for any damage, or infringement of any third-party's rights, originating in the use of any product data, diagrams, charts, programs, algorithms, or circuit application examples contained in these materials. 3. All information contained in these materials, including product data, diagrams, charts, programs and algorithms represents information on products at the time of publication of these materials, and are subject to change by Renesas Technology Corp. without notice due to product improvements or other reasons. It is therefore recommended that customers contact Renesas Technology Corp. or an authorized Renesas Technology Corp. product distributor for the latest product information before purchasing a product listed herein. The information described here may contain technical inaccuracies or typographical errors. Renesas Technology Corp. assumes no responsibility for any damage, liability, or other loss rising from these inaccuracies or errors. Please also pay attention to information published by Renesas Technology Corp. by various means, including the Renesas Technology Corp. Semiconductor home page (http://www.renesas.com). 4. When using any or all of the information contained in these materials, including product data, diagrams, charts, programs, and algorithms, please be sure to evaluate all information as a total system before making a final decision on the applicability of the information and products. Renesas Technology Corp. assumes no responsibility for any damage, liability or other loss resulting from the information contained herein. 5. Renesas Technology Corp. semiconductors are not designed or manufactured for use in a device or system that is used under circumstances in which human life is potentially at stake. Please contact Renesas Technology Corp. or an authorized Renesas Technology Corp. product distributor when considering the use of a product contained herein for any specific purposes, such as apparatus or systems for transportation, vehicular, medical, aerospace, nuclear, or undersea repeater use. 6. The prior written approval of Renesas Technology Corp. is necessary to reprint or reproduce in whole or in part these materials. 7. If these products or technologies are subject to the Japanese export control restrictions, they must be exported under a license from the Japanese government and cannot be imported into a country other than the approved destination. Any diversion or reexport contrary to the export control laws and regulations of Japan and/or the country of destination is prohibited. 8. Please contact Renesas Technology Corp. for further details on these materials or the products contained therein.
RENESAS SALES OFFICES
Refer to "http://www.renesas.com/en/network" for the latest and detailed information. Renesas Technology America, Inc. 450 Holger Way, San Jose, CA 95134-1368, U.S.A Tel: <1> (408) 382-7500, Fax: <1> (408) 382-7501 Renesas Technology Europe Limited Dukes Meadow, Millboard Road, Bourne End, Buckinghamshire, SL8 5FH, U.K. Tel: <44> (1628) 585-100, Fax: <44> (1628) 585-900 Renesas Technology (Shanghai) Co., Ltd. Unit 204, 205, AZIACenter, No.1233 Lujiazui Ring Rd, Pudong District, Shanghai, China 200120 Tel: <86> (21) 5877-1818, Fax: <86> (21) 6887-7898 Renesas Technology Hong Kong Ltd. 7th Floor, North Tower, World Finance Centre, Harbour City, 1 Canton Road, Tsimshatsui, Kowloon, Hong Kong Tel: <852> 2265-6688, Fax: <852> 2730-6071 Renesas Technology Taiwan Co., Ltd. 10th Floor, No.99, Fushing North Road, Taipei, Taiwan Tel: <886> (2) 2715-2888, Fax: <886> (2) 2713-2999 Renesas Technology Singapore Pte. Ltd. 1 Harbour Front Avenue, #06-10, Keppel Bay Tower, Singapore 098632 Tel: <65> 6213-0200, Fax: <65> 6278-8001 Renesas Technology Korea Co., Ltd. Kukje Center Bldg. 18th Fl., 191, 2-ka, Hangang-ro, Yongsan-ku, Seoul 140-702, Korea Tel: <82> (2) 796-3115, Fax: <82> (2) 796-2145
http://www.renesas.com
Renesas Technology Malaysia Sdn. Bhd Unit 906, Block B, Menara Amcorp, Amcorp Trade Centre, No.18, Jalan Persiaran Barat, 46050 Petaling Jaya, Selangor Darul Ehsan, Malaysia Tel: <603> 7955-9390, Fax: <603> 7955-9510
(c) 2006. Renesas Technology Corp., All rights reserved. Printed in Japan.
Colophon .6.0

▲Up To Search▲

Price & Availability of HA17324AF

	To Download HA17324AF Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .